How To Use Corn Thresher Better

• Posted by luu hongxiang May 18, 2021 - Filed in Business - #Corn Thresher  #China Rice Planting Machine  - 628 views

  The threshing speed of Corn Thresher seriously affects the life of the corn thresher. Excessive threshing will cause the internal parts of the corn thresher to be shaken and damage the thresher manufacturer, shorten the service life and the cleanliness of threshing.

   

  It is undoubtedly the rotational speed that affects the threshing speed. Generally, the rotation speed is controlled at 29m/s. If the rotation speed is too high, the corn kernels will be crushed, and if the rotation speed is too low, the corn will be unclean.

   

  The speed of the thresher should not be too fast, it should be used according to the speed specified in the instruction manual, and the speed cannot be increased arbitrarily. Generally, it is 28-32 m/s for wheat removal, 24-26 m/s for indica rice, and 26-30 m/s for japonica rice. If the rotation speed is too high, not only will it not take off quickly, but it will also cause serious crushing of the grain, shorten the service life of the machine, and increase the unsafe factors. It is necessary to install a matching electric motor or diesel engine according to the requirements or the signs on the machine, and be equipped with a suitable pulley, and be careful not to install it in the opposite direction. The fan rotating pulley can not be installed reversely, otherwise it will affect the cleanliness of the grain.

  Reasonable use of corn thresher can better extend the service life of corn thresher, so as to be a better helper.

   

  Due to seasonal restrictions, seasonal machinery varieties such as corn harvesters, wheat harvesters, threshers, soybean harvesters, etc., have shorter working hours each year.

   

  Corn thresher series, harvesters, etc. only work more than ten days a year, and the storage time is long. If they are not properly kept, the damage of the machine during the parking period will far exceed the damage during the work.

   

  The form of damage to the machine during storage

   

  Mildew: mainly textiles, such as canvas conveyor belts. These products should be removed, washed and dried, and stored in a dry place indoors that can prevent pests and rodents.

   

  Aging: Due to the effects of oxygen in the air and ultraviolet rays in the sun, the rubber parts are easy to age and deteriorate, which makes the elasticity of the rubber parts poor and easy to break.

   

  Corrosion and cracking Wooden pieces decay and crack due to the action of microorganisms, rain, wind, and sunlight.

   

  Deformation: Some parts undergo plastic deformation due to long-term stress or improper placement. Such as springs, belts, long blades, tires, etc.

   

  Corroded metal will be corroded by the action of oxygen and water vapor in the air. Corrosion is the most harmful to the surface of parts and thin steel products with a thickness of 1 to 1.50 mm. For example, the corrosion depth of thin steel plates placed in the open air can reach 0.10 to 0.22 mm in a year, and it will be scrapped in a few years. Corrosion also has certain hazards to section steel, especially the thinner parts with lower parts that are susceptible to moisture and stagnant water. Rust does little harm to iron castings.

  Others: such as damp electrical equipment, self-discharge of batteries, etc.

   

  Storage Measures for China Rice Planting Machine

   

  The yards, sheds and warehouses for storing machines and tools should be kept clean. The equipment parked in the open should be set off the ground with bricks or the equipment to reduce corrosion.

   

  When the machine is out of service, it should be carefully inspected, cleaned and maintained. Damaged parts should be repaired or replaced in time.

   

  The working surface of metal parts should be coated with anti-rust oil, of which paraffin oil has better anti-rust effect. Thin steel plates, section steels and wooden parts should be painted. The paint is divided into two types: top coat and primer, and the primer and the machine parts are firmly joined. There are many types of paints, and their anti-rust and anti-corrosion effects are different, so they should be selected reasonably according to the service conditions of the parts.

   

  Remove the perishable parts and keep them in the warehouse. Cotton products, electrical equipment, etc. should be placed in a dry place. Rubber products should be placed indoors out of direct sunlight, or covered outside. Batteries are expensive and easy to vulcanize when stored for a long time. They should be charged regularly according to regulations.